LOMBARDINI FOCS ENTRETIEN PDF

Home>FILTRES>KIT REVISION>KIT 3 FILTRES ADAPTABLE LOMBARDINI FOCS ET PROGRESS AVEC CARTOUCHE GO. (except where indicated in this manual). • Stop the engine before Diesel engine: LOMBARDINI mod. LDW FOCS • Keep the diesel engine running . FOCS Workshop Manual_cod. _1° ed_ rev. CHAPTER INDEX – This manual contains pertinent information regarding the repair of LOMBARDINI .

Author: Murisar Daitilar
Country: Djibouti
Language: English (Spanish)
Genre: Literature
Published (Last): 3 July 2007
Pages: 72
PDF File Size: 15.16 Mb
ePub File Size: 3.84 Mb
ISBN: 653-4-69197-297-1
Downloads: 30332
Price: Free* [*Free Regsitration Required]
Uploader: Moshakar

Continue the periodical maintenance afterkm by starting from 7, km. Disconnect the accelerator control rod from the rntretien control lever 3 fig. Inside of radiator or coolant lines obstructed. If the free height A is less than 43,5 mm replace the spring.

Tighten the nut 1 by hand until the belt tightener rests on surface of the crankcase. If the rings are black it means lombardinii 3 and 4 of the crankshaft are tempered. Insert the spark arrester in the injector housing with surface A pointing upwards.

Do not route the welding lead over or near the wiring harnesses of lombardnii engine or plant. Pistons at the nominal diameter are only supplied in category A.

WORKSHOP MANUAL 1003 FOCS Engine Series – lombardini service

We share information about your activities on the site with our partners and Google partners: Remove the closing caps 4 at the end and carefully clean inside. Remove the piston rings and clean the slot. Wear protective gloves to avoid touching used oil.

Read Also:  BAIT OF SATAN JOHN BEVERE EBOOK DOWNLOAD

Pumping Element old-type Injection Pump Remove the cap from compensation tank cap and check that the liquid is at the correct level. Checking level and adding engine oil. When re-fitting introduce the the new pre-combustion chamber into the cylinder head so that the side hole of the pre-combustion chamber aligns with the glow-plug hole.

Injection Advance Control And Regulation Disareazione Del Circuito Di Raffreddamento Static Injection Advance Regulation Valve guides with outside diameter B increased by 0. Voltage Regulator Connections With 2 camshaft on the cylinder head. The tank must only be lombardni when the engine is off. Valve guides are supplied in finished form, further machining is prohibited.

Lombardini LDW 903 Manuals

Water cooled Diesel engines http: When discontinuing use of the engine, select all components according to their chemical characteristics and dispose of them separately.

Summary Of First Maintenance Operations When pulley reference mark A aligns with the timing cover reference mark B, the flywheel side piston is at TDC. Camshaft, journal and housing measurement Use an inside micrometer gauge for housing diameters and an outside micrometer gauge for journal diameters.

Never carry out any operation whilst the engine is running. Insert the ring gear into its seat and place it carefully on the rim fos the flywheel.

Lombardini Diesel Engine Part Manual Ldw –

Fuel lift pump Components: Both for crankshaft bearings and for connecting rod big end bearings internal diameter are undersized by 0. For clearance values between the journals, connecting rod pin and the relevant bearings see page Always replace it and mount it with especial care above all in zones 1 and 2 where, for greater safety, it is advisable to apply a few drops of silicon sealant. Then rotate the crankshaft until the TDC is read in the dial gauge.

Read Also:  POTAIN MDT 178 EPUB DOWNLOAD

Alternator Battery Charger Curve 12v 20a ON-OFF sensor control cam Tighten oil drain plug at a torque of 40 Nm. Thickness of half-rings is equal to 2.

Using piston ring compression pliers, introduce the piston into the cylinder so that combustion chamber A is directly under the precombustion chamber parallel tocs the head. Bad operation of the speed governor can cause serious damage to the engine and to people being near to it. Alternator, Iskra 14v 33a – Performance Curve Central Main Bearing Caps Cada Horas Cada Horas Use the special tool “” 1 to romve the ring nut 2. Redo the consumption check on the stabilised engine.

Rotate the crankshaft until the unit injector cam lobe 2 forces the cam follower 1 to the lombardiji position, then insert a suitable sized hardened pin into the hole 3 and rotate the crankshaft until the cam follower 1 is at the lowest position.

Required Settings as Most Commonly Applies